Keysight N9951A | FieldFox handheld µW combi analyzer 300 kHz to 44 GHz, USB 2.0, LAN, rechargeable battery
Manufacturer number: N9951A
On Request
Keysight N9951A | FieldFox, handheld combination analyzer 300 kHz to 44 GHz.
- Frequency range: 300kHz to 44GHz
- Directivity >42dB
- Dynamic range 100dB
- DANL: -153 dBm (specified), typical -158 dBm at 2.8 to 4.5 GHz
- Typical output power (6.5 to 18 GHz): 4 dBm (frequency dependent)
- Flat output power frequency response (± 0.5 dB) at an output power of -15 dBm in the frequency range 300 kHz to 44 GHz
- Output power adjustable in 1 dB steps
- Transmission and reflection measurements (S21, S11) or with optional 2-port measurement (S21, S11, S12, S22)
- Reflectance measurements (RL, VSWR and scalar measurements)
- TDR cable measurements
- Cable attenuation, reflection loss, distance to fault location
- Built-in power meter: 5 kHz to 26.5 GHz
- Optional power measurement by Keysight USB RF power sensor. frequency range depends on the type of power sensor used)
- Vector volt meter comparing phase and electrical cable length
- Integrated test connection for S-parameter determination and for error distance measurement in cable measurements
- Battery life 3.5 hours
- Closed housing, dustproof, without fans etc.
- Water repellent; resists salty and humid influences
- Meets the requirements of: IEC/EN 60529, MIL-PRF-28800F Class 2 and MIL-STD-810G, Method 511.5, Procedure I (conditions for use in potentially explosive atmospheres)
- Dimensions: Width: 188mm, Height: 292mm, Depth: 72mm
- Weight: 3.2kg
Typical areas of application:
- satellite communications
- mobile communication
- Measurement of the connection in a communication system (e.g. GSM) to the operative backbone system
- radar technology
- Aerospace and defense technology
- Active and passive component and module test
Options:
For use as a Vector Network Analyzer (VNA) and for cable testing:
- Time domain analysis (TDR measurements)
- VNA reflection and transmission measurements
- VNA: 2-port S-parameter test (S21, S11, S12, S22)
- 1-port mixed-mode S-parameter test
- TDR cable measurements (distance to fault)
- Vector voltmeter
For use as a spectrum analyzer:
- Extended range for transmission analysis (ERTA / Extended Range Transmission Analysis)
- Tracking generator over the complete device frequency range
- Spectrum analyzer option
- preamp
- Interference analyzer and spectrogram
- Timegating option for spectrum measurements
For RF power measurements:
- Frequency dependent USB RF power measurements
- USB interface for connecting USB RF power sensors
- Integrated power meter to measure over a user-definable frequency range
- Pulse measurements (radar) with a peak RF power meter
For general system properties:
- GPS receiver
- Variable DC voltage source 1 V to 32 V, 650 mA max and 8 W max
- remote control
Note: This list does not claim to be complete. Before ordering, please consult our office staff
Description
N9951A | FieldFox handheld µW combi analyzer 300 kHz to 44 GHz, USB 2.0, LAN, rechargeable battery
The basic version of this combination device N9951A is equipped as a cable and antenna test device and covers the frequency range from 300 kHz to 44 GHz. This combination device is intended for rough field use in its basic configuration for cable and antenna measurements. Optionally, this FieldFox N9951A can be expanded as a spectrum and vector network analyzer, thus enabling direct transmission and reflection measurements S11, S21. The integrated HF power measurement option offers measurement of the HF signal power at the push of a button over a bandwidth that can be defined by the user. With an optional extension, USB power sensors can also be connected directly. By using USB peak power sensors, the pulse peak power and the average power can be measured on radar systems in order to have the ratio of peak power to average power displayed directly.
With this device you have Keysight quality and accuracy in your hands - because it is portable, fits well and is easy to use.
With optional configuration options , the system can be expanded into a 2-port S-parameter test system, which means that all S-parameters can be measured. With additional optional and retrofittable equipment, the device can be adapted to the respective application with many other options (see list at the end of this description).
It should be emphasized that this device can be equipped with a tracking generator covering the entire frequency range of the device.