Gossen Metrawatt M535L | Profitest MTECH+ IQ basic device VDE 0100 stationary test device
Manufacturer number: M535L
Gossen Metrawatt M535L | Profitest MTech+ IQ test device / installation tester VDE 0100 / IEC 60364.6 tests.
- Loop and line impedance measurement
- Measurement of insulation resistance with nominal voltage, with variable or increasing test voltage
- low-impedance measurement
- earth resistance measurement
- site isolation measurement
- Universal connection system
- Display of permitted fuse types for electrical systems
- Testing of the start-up of energy consumption meters
- Calculation of line lengths for common cross-sections of copper lines
- Measurement of bias, leakage and compensating currents up to 1 A and working currents up to 150 A using the Clip 0100S current clamp sensor as an accessory
- Measurement of the rotating field direction (phase sequence, highest phase-to-phase voltage)
- Testing of residual current devices (RCD circuit breakers)
- Measuring touch voltage without tripping the switch. Here, the touch voltage related to the nominal residual current is measured at 1/3 of the nominal residual current.
- Tripping test with nominal residual current, measurement of tripping time
- Special tests of systems or RCD circuit breakers
- Testing of systems or RCD circuit breakers with increasing residual current with display of the tripping current and the contact voltage at the moment of tripping.
- Testing of RCD circuit breakers with: ½ × IΔN, 1× IΔN, 2× IΔN, 5× IΔN
- Testing of RCD circuit breakers suitable for pulsating DC fault currents; the test is carried out with positive or negative half-waves
- Testing of RCD circuit breakers with adjustable residual current to determine the contact voltage and the tripping current
- Testing of special RCD circuit breakers: selective S, SRCDs, PRCDs (Schukomat, Sidos, etc.), type G/R, type AC, type A; Type B
- Testing of residual current (RCD) protective circuits in IT networks
- Editable test sequences
- Bluetooth interface for using the ProfiScan APP
Technical Data
All-current sensitive RCDs type B, B+: | Yes |
---|---|
Article number: | M535L |
Automatic test sequence: | Yes |
Check residual voltage: | Yes |
Counter start-up: | Yes |
DIN VDE 0100 / IEC 60364-6: | Yes |
Dimensions (L x W x H) (mm): | 260 x 330 x 90 |
Insulation measurement 50V: | Yes |
Insulation measurement 100V: | Yes |
Insulation measurement 250V: | Yes |
Insulation measurement 325V: | Yes |
Insulation measurement 500V: | Yes |
Insulation measurement 1000V: | Yes |
Interfaces: | USB |
Measured value memory: | 50000 |
Mobile: | Yes |
Model: | PROFITEST MTECH+ IQ |
Rotating field direction: | Yes |
Selective, SRCDs, PRCDs, type G/R: | Yes |
Software included: | Izytroniq |
Stationary: | No |
Touch Display: | No |
Voltage drop: | Yes |
Warranty (years): | 10 |
Weight (kg): | 2.7 |
e-Mobility (prepared): | Yes |
Documents & Downloads
Description
M535L | Profitest MTECH+ IQ basic device VDE 0100 stationary test device
The Gossen Metrawatt M535L PROFITEST MTECH+ IQ supports you in testing the effectiveness of protective measures on stationary electrical installations. You can use both programmable and predefined test sequences that comply with test standards such as VDE100-600 or EN 50110-1.
Due to the high memory concept and the programmability, the test device is extremely user-friendly. A wide-range measuring device enables the test device to be used for all AC and three-phase networks with voltages from 65 to 500 V and frequencies from 15.4 to 420 Hz.
Protective measures in electrical systems are intended to protect human life from accidents involving electricity and thus ensure its integrity. Of course, they should also protect material values from damage caused by electricity. Every electrical installation must be tested with this VDE test device before it is put into operation for the first time and then at regular intervals for the effectiveness of the existing electrical protective measures. Your advantage: low-impedance, insulation, earth resistance, site insulation, loop and network impedance measurement and legally compliant documentation in one test device.
Lieferumfang
- test device
- Safety plug insert (PRO-Schuko)
- 2-pin measuring adapter
- Extension cable to 3-pin adapter (PRO-A3-II)
- alligator clips
- shoulder strap
- battery pack
- charger
- Quick User Guide
- Operating Instructions (on CD-ROM)
- DAkkS (DKD) calibration certificate included
- License code for logging software IZYTRONIQ BUSINESS Starter (can be downloaded from the Internet)
PC user software IZYTRONIQ:
- IZYTRONIQ is testing software that has been newly developed from the ground up
- Flexible, subsequently expandable software - adapt IZYTRONIQ to your individual requirements
- Map the entire test process across devices, manage and document in an audit-proof manner
- Combine measurement and test data from different test devices and multimeters into one test
- IZYTRONIQ automatically recognizes and manages the connected test devices. The software intelligently determines the range of functions available on your devices
- Optimized for both stationary and mobile use - create test documentation directly on site, without subsequent processing
- Intuitive operation, understandable and simple - intelligent marking and hiding of tools and workspaces
- Pioneering design with meaningful icons. Complex database connections are shown in simple tree structures
Accessoires (15 products )
Recommendations (9 products )
News and Knowledge
dataTec unboxed is the new video series from dataTec for product presentations and news from the world of measurement an...
The DIN VDE regulations govern the electrotechnical regulations as defined by DGUV V3 (accident prevention regulations f...
Thomas Schleich is an engineer, an expounder of ideas, a free spirit – and a first-class speaker at the dataTec Academy....